In case you’re on the lookout for a spot to retailer your firewood that is also tremendous cool to take a look at, take a look at this firewood holder DIY. Earlier than, I might simply have my totally different sizes piled up in containers across the fireside, which was actually unattractive. So on a whim I threw these collectively. The three compartments permit me to separate small, from medium, to giant items of wooden. Seize a set of plans and let me present you the way I construct them.
Let’s Construct A Firewood Holder
DIY Firewood Holder Plans
$9.99
I’ve created a set of plans to make constructing this firewood holder fast and simple!
Supplies I Used on this Construct:
Step 1: Deciding on Materials and Slicing to Measurement
I did design and construct these on a whim so when choosing materials, I simply regarded round my store to see what I had already that will match the sizes. I discovered this stack of three/4” lower off from some cabinets I tore a component that I’ll make the physique from. Then for the again, I’ve some 1/2” plywood from who is aware of what.
I began off by ripping the sheets all the way down to width wanted. If you would like precise dimensions, I’ve a set of plans obtainable over on my web site. I tilted the blade over to then lower within the angles wanted to created the pointed miters. Since there are a number of repeated components, I arrange a cease block in order that I may make all of them the identical. Whenever you do that, you wish to be sure that to set the cease block again far sufficient so the board received’t be touching it when it contacts the blade. As that is what may cause relax.
To avoid wasting from switching the blade forwards and backwards, after reducing one aspect with the wanted angle, I might flip the board and lower the opposite aspect because it nonetheless had a 90 on one finish. This may depart the remaining board with angles on each finish, that I can chop up for the mitered components. I personally wish to all the time do a check first and a dry match to verify issues are going to work as I’ve them deliberate. That appears good although.
Step 2: Banding the Edges of the Firewood Holder
Now I simply wanted 12 of them complete so I locked within the new distance for the fence for this half and chopped up the remaining bit into items.
This venture solely consist of 4 totally different components. What I’ll name the aspect, the tops that are barely longer than anything, the horizontal cabinets, then the mitered factors. Remember the fact that it could be easy so as to add extra to subtract the variety of cubbies, relying in your areas wants.
Alrighty, now I’ll edge band the perimeters that might be going through the entrance. Really, on second thought, I like the concept of portray them as an alternative. Notice: that in case you edge band you’ll want to try this earlier than becoming a member of the components collectively, however if you wish to paint, then you possibly can go straight into assembling.
Step 3: Assembling the Firewood Holder Cubicles
For assembling, I began off on prime of my workbench and what I did is apply some wooden glue, I’m utilizing DAPs weldwood right here, to each joint, then pin nailed issues collectively utilizing my 23 gauge nailer. This can be a fairly weak joint till the wooden glue has time to arrange, so I used to be being cautious as I used to be shifting it round to connect the subsequent leg. If I didn’t have a 23 gauge, I might have used a 18 gauge as an alternative.
After getting a number of connected, I assumed it could make issues simpler to do it on the bottom so I may see all the things clearly as I used to be attaching legs. So I moved it all the way down to the ground and continued. I might juke and jive to create the factors of the cubbies, then connect the horizontal that can create the separation between.
I paused once I bought to the very prime as a result of the way in which I’ve it designed, the highest edge will really be seen. With that, I edge banded each of those components earlier than including them on. This is so simple as heating up an iron and warming up the glue on the again of the banding till it sticks to the plywood edge. This might be barely totally different than the ply, nevertheless it doesn’t trouble me.
Step 4: Portray the Firewood Holder Cubbies
I left that the place it sat to present that glue time to arrange and dry. Whereas it was, I grabbed items that can make up the again from my 1/2” plywood scraps. I additionally grabbed the items that can make up the edges. I would like each of those to be painted the identical shade as my wall which implies I would like to present them a number of coats earlier than attaching the cubbies.
Since I’ve the paint out, I additionally wished to color that entrance fringe of the cubbies. I first give them each a superb sanding to get them clean. Now when working with plywood, there are sometimes voids on each single edge. To be able to get a clean trying paint floor, I apply some wooden filler on a putty knife. I’m utilizing DAP Premium wooden filler. These items not solely dries quick however is straightforward to sand and is nice to paint match if you’re staining one thing.
After letting it dry for about 30 minutes, I got here again with a sanding sponge to knock it down flat in order that I may roll on the paint onto the items of the firewood holder.
With ending out of the way in which, let me simply push this button right here to boost my ending shelf up and find the {hardware} I’ll want to connect the cubbies to the again.
Step 5: Shaping the Again to Match the Firewood Holder Cubbies
I began with a again barely bigger than what I wanted, then plopped the cubbies down onto it and lined it up in order that the underside cubby was flush to the top of the plywood. I used my pin nailer to only tack issues in place to begin. The top is straightforward accurately flush, however to verify the remainder weren’t crocked, I pulled a tape to get the spacing good earlier than tacking the remainder. With it not capable of fall off now, I tilted your complete unit on it’s face in order that I might have entry to the underside to throw in screws. Right here, I made certain to pre drill to stop splitting.
Step 6: Securing the Firewood Holder Cubbies to the Again
The highest location is straightforward to find as a result of you could have a visible on the place the shelf is positioned. Nevertheless, the second is difficult as a result of it’s in the midst of nowhere. What I do is seize a pace sq., this Crescent one has an extra 6” flip out rule in order that I can place it within the heart of the shelf, go all the way down to the dimension wanted, and pre drill. In case you don’t have this pace sq. or one other lengthy one, then a stage would additionally do the trick.
For the angled portion of the cabinets, the pace sq. wouldn’t work, so I grabbed a scrap and lower in an angle on the tip. This fashion I may relaxation it on the shelf and permit me to mark the peak. Ensuring to maintain it in the identical location, I moved the scrap to the face closest to me to now drop it down again to the road I made which supplies me the placement of the angled shelf to pre drill and fasten a screw.
With the again on, this factor now feels actually safe and robust. I flipped it up to have a look. I really suppose it seems to be fairly good with a sq. again on it and was contemplating leaving it as is however then I made a decision to stay to my authentic plan and make the again flush to the geometric form. I wasn’t capable of find my palm router, which is definitely the best instrument to trim the again off, so as an alternative I put a flush trim bit in my router desk and trim it off that manner. The important thing right here is to maintain the unit good and flush on the desk as you progress it alongside.
I laid the unit over and connected the aspect. This may assist help the horizontal cabinets that can really be supporting the load of the firewood.
Step 7 : Putting in the Firewood Holder and Slicing Firewood
Very last thing to do was set up them. Now I personally wished mine up off the bottom so I wouldn’t block an outlet I’ve over on the correct hand aspect. Then I additionally like to make use of this space for storing my video games and puzzles. With that, I propped the items up, discovered the studs, then drove a number of screws into the again of the unit to connect them.
Okay lets load it down and see how a lot it will possibly maintain. Now that, is a lot better than earlier than. As a substitute of ugly bins and totes, I now have a pleasant firewood holder with devoted area for the wooden. This may permit me room to retailer and separate all totally different sizes of firewood throughout winter. Then I personally just like the look of wooden sufficient to maintain it full yr spherical, however I may additionally retailer other forms of nicknacks throughout spring and summer time ought to I wish to.
What do y’all take into consideration them? Bear in mind how simple it’s to make bigger or smaller. I even suppose they might look good horizontal, relying in your area. I’ve a set of plans for this venture in addition to many different over on my web site. In truth, in order for you firewood storage concepts, I’ve a number of of them.
I’ll see you subsequent time.