Let’s Construct a Laundry Drawer!
DIY Laundry Drawer Plans
$9.99
Supplies I Used to Construct the Laundry Drawer
Step 1: Slicing Items for the Drawer
It takes 7 components to make the physique. So not many. If you want a set laundry drawer plans with dimensions then I’ve that out there, it additionally comes with a CNC lower file if in case you have a CNC. I personally painted my cupboards so I simply used no matter 3/4” sheet materials I had scraps of which is MDF on this case.
I begin by laying the facet items on their again and attaching what would be the backside. When becoming a member of issues collectively, will probably be the identical course of on every little thing, I used DAPs weldwood wooden glue then predrill and run in a screw
Step 2: Getting ready the Toe Kick Plate and Attaching Laundry Drawer Sides
This ledge right here will likely be the place the toe kick plate goes in, which is that this board right here. I’m utilizing it as a spacer to verify the underside is connected sq.. After utilizing it to align the board from the within, I additionally used it as a spacer to information me on the place to pre drill and run in a screw. Double checking that it labored; it did, so I proceed attaching. I used this trick once more once I wanted to run within the heart gap. So long as the board is flush to the entrance, it’s going to point out the place the three/4 materials begins for the pre drill gap.
After attaching the primary facet, I connected the second facet the identical method. Nonetheless because the toe kick now can’t match inside to test for sq., I simply used a tape. I measured the highest, then made certain the underside matched earlier than driving in my screws to connect it.
Step 3: Attaching the Toe Kick Plate
Subsequent is to connect the toe kick, which ought to line up completely flush to each of the facet items and the entrance and the again. Identical with the again board that can make up the again of the platform as soon as this cupboard is stood up proper. Excellent, that’s the backside completed so now lets flip this round, however nonetheless go away it on it’s again, and begin engaged on the highest boards. This board right here will be a part of the edges out on the again edge whereas additionally giving me a spot to screw it into the wall in a while when putting in it within the house.
When becoming a member of one thing flush like this, I like to maneuver my work piece to the sting of my workbench if potential. This manner my drill has room to go in straight as an alternative of at an angle the place I might blow out a screw.
Step 4: Attaching the Final Board
The final piece to connect here’s a related board because the final however this one joins the entrance fringe of the edges. Since I can’t use my workbench to relaxation it towards, what I love to do is use a clamp to behave as a 3rd hand. These squeeze clamps are nice to carry them within the normal space whereas I get one facet at a time completely positioned and connected. This board will give me one thing to screw up right into a countertop later when it will get put in.
Step 5: Including the Again to the Laundry Drawer
Okay, with that connected, now let me spin this round, tilt it up, and identical to that now we have a cupboard. Oh, I forgot the again. Maintain on, that’s a fast add. Lets simply lay this factor again down, however this time laying it on it’s face. I made the again from 1/4” mdf because it doesn’t should be tremendous thick. 1/4” materials will do a fantastic job at holding it sq. and retaining it from racking.
You’ll see that my again is in two items. That’s as a result of I’m utilizing scraps and don’t care concerning the again, which will likely be on the within and by no means seen, has a appear. If it does trouble you although, you’ll be able to at all times make it from one stable piece
Alrighty, and now that’s a accomplished physique. So for now, lets simply slide this on over to make room for me to herald the components to construct out the within drawer that can maintain the baskets.
Step 6: Securing the Match and Attaching the Sides
All of those components are additionally included on the plans and cutlist however I seize for what would be the backside first. I personally at all times like to verify it matches throughout the physique earlier than attaching issues simply because I’ve been identified to seize the mistaken half earlier than however as soon as I made certain it match, I connected the 2 sides which appear like wings. These have dados lower into them for the underside to slide proper into.
This backside will likely be locked in as soon as the back and front are connected, however I went forward and threw in just a few screws. I went to the again and connected the specialty designed again. These slots and these predrilled by holes are wanted for the below mount drawer slides that I’ll be utilizing.
In case you use my precise dimensions then you cannot solely use the precise hampers that match on this laundry drawer but additionally the precise drawer slides. Nonetheless, know that if you wish to change dimensions then you definately’ll most likely need to get totally different drawer slides and alter the design of this again half. Another choice is to alter the size to what you need, however then use facet mount drawer slides and never fear concerning the below mount ones. Numerous choices.
Step 7: Finishing the Entrance Meeting
Going to the entrance of this meeting, I connect the massive entrance panel. This might sound massive and boring proper now however you’ll see why the size is required. For now, let me go forward and put it contained in the physique to verify all of it appears good……annnnd it does. It’s so simple as that, now every little thing right here on out are ending particulars.
Step 8: Making the Laundry Drawer Slide!
I might connect the below mount drawer slides to the underside facet of the cupboard. Appears to be like like this right here. Then go to the within of the cupboard and fasten the rails with screws. To attach the 2, I might carry the within portion over to the physique, set it on the rails, then push it in till the 2 elements clicked collectively. It’s so satisfying. Then since I’m making mine appear like two doorways and a high drawer, I crawled inside and connected these items to the skin by screwing them in on the within whereas Jacob held them to the correcting spacing.
Conclusion: The Completed Product
It’s kinda exhausting to get a great angle of this cupboard as a result of the house is admittedly tight however with out the counter high in place you’ll be able to see the way it works. Two hampers match completely on the drawer as a way to pull it out and toss in your garments, then conceal them away once more by pushing it in. Gentle closed in fact.
Even with the countertop on, I’ve loads of room to take the baskets out and in or just toss in garments then reshut it. I like the way it appears like three elements. The place because the unit on the left actually is a high drawer and two doorways on the underside.
I’ve a 4 half sequence of movies the place I cowl methods to correctly paint MDF, methods to construct customized cupboards, methods to improve retailer purchased cupboards, and in addition methods to construct a countertop from scrap 2x4s! So principally if you wish to see how I constructed out your complete room you’re , then test the hyperlinks within the description. In case you can think about it, you’ll be able to construct it and I hope I’m an inspiration or information that can assist you get began. I’ll see you on my subsequent undertaking.
